A shelf library is certainly one of the most simple furniture that can be achieved as it is to assemble a structure of rectangular shape, formed simply by two sides and a number of shelves, possibly equipped with closing doors. Following this guide will realize a library chipboard, which is of particular interest because the Rainier and doter of appropriate lighting.

Start cutting out the shapes. Then, on the panel that serves as the lower shaped element, the foot, supports a rectangular aperture in the carton, with curvature at the top of fifty-eight centimeters in radius. Aquinas trace its outline. At this point, the same operation must run it on the top panel that will act as a head. The radius of curvature of the template is of thirty-seven cm, then ponytail tangent to the upper edge.

Now make the cuts on veneered chipboard using the jigsaw, following the trail leaving visible along the part that you have to keep. In order to make precise changes of direction of the blade, practice of the through holes tangents to the point where it has the sharp curve with the drill. Cut edges carefully diamante the file rasp as difficult with a saw you can cut a perfectly straight. You will need to give a further finishing with abrasive paper wound on a rubber pad so as to make the most possible smooth rounded edge.


At this point, to practice the openings in which are you going to enter the lamps, u knows a hole saw to fifty millimeters and make two holes whose centers are eighty millimeters . As soon as you have them made, with the jigsaw removed the particle board that connects the two holes, after drawing the tangents to these, as noted in the picture of this step. Now, before with the file rasp, then with sandpaper, regulates the cut parts with the jigsaw the edges.

When you have done this work, with the drill practice a through hole that connects the opening just implemented with the front edge of the shelf, to allow the passage of the electrical cable. Now, the front edges of the shelf will need always with the jigsaw so as to leave space for the rods of the sidewalls. Now practice with the circular saw, along a short side and part of the front, a groove sufficiently deep and wide to house the electric cables.

At this point, add the cable supplying the bulbs in the groove and, along this applies the silicone sealant or hot glue. At this point, prepares a wooden block with two holes in which you will need to enter the lamp holders with the legs pointing upwards with care. Supports now a holder on the Haldane and feet together so that they are paired and opposed, as noted in the picture of this step. Welds also a nail head without keeping it in a horizontal position. Enter the pair of sockets in the opening, driving the nail into the wood, then weld the ends of the wires to the pins.

Once done, slotting the rods, he created a wooden handle that house them, then practice centered longitudinal cuts using a circular saw or drill. At this point, you will need to refine the groove thus obtained with a planer and with abrasive paper. When you run the job, the ends of the rods of the shelves. so you can connect seamlessly with the vertical rods of the hips.

In this phase of the work, switch to lock the shelf securely in a vice and apply the glue in the groove of the rod ramie. Once done, also apply the glue on the front edge of the shelf. Then place the rod and applies the bindings tight until the glue is completely cured. Now track, in the lower part of the flanks, the area to be removed to create the seat of the wheels and the space on the front edge to the head of the rod which must be screwed.

At this point, performs a downward also on the other end of the front edge of the sidewalls. Then, with the guide drill, practice holes along the edges of the foot, the shelves and head for the insertion of the pins, as well as showing you the picture of this step. When you have done this, go into the holes previously drilled to insert markers type cap, which will submit a tip accumulation the center.

Now, supports an element at a time on a side, in the final position of mounting, then beat with the rubber mallet so that the tips leave clear traces. At this point, at the points where there are the traces practice the blind holes for the plugs and repeat the process with all the elements on the other side. Now practice on the rods by forty millimeters deep groove centered twenty millimeters , that they get to fifty and thirty other from one end, it will need to round it. Then apply the glue and place them around the edges of the sides beating with a rubber mallet.

Now, before proceeding to the final assembly, paint all the members of the cabinet with painting the Ralina, but you can also use other paint or varnish. Then mounts the whole. At the rear, between the sides and behind the edges of the shelves, applied with glue and screws the wide sheet of plywood which acts as a backrest, positioning it between the head and foot. Fixed on the back of insulated connectors that allow to derive, from the main line power, lighting circuits of each shelf.

Having reached this point, switch to pierce the lower end of the rods located along the edges of the sidewalls so as to be able to insert the pin for the wheels. Once done, on the visible side of the backrest applies a series of Semite PVC cut lengthwise and glued with adhesive better, with hot glue. Finally, the opening where the cone inserted pairs of bulbs you will need to close them with a piece of opal Plexiglas , which lets a diffuse light, gluing with contact cement.